 |
|
|
|
|
|
|
|
|
Shotgun Side Sling Mount Plate
SPECTER-DIRECT
Side mounting is the only way to properly mount a "3 Point" tactical
sling. Until now there has been no way to do this with a Mossberg 500 shotgun.
This sling mount plate installs underneath the magazine bolt and locks in place
by ball detent. The sling plate is made from steel, has a matte black finish,
accepts up to 1 1/4" wide slings and is completely ambidextrous.
Note: Requires a simple modification of the magazine bolt. For more information
see our magazine bolt modification instructions.
|
G. G. & G. M-4 / CAR-15 Receiver Sling Mount (Rectangular Type)
SPECTER-DIRECT
Allows receiver side mounting of our CQB, SOP and HST slings on collapsible stock M-4/CAR-15 type weapons. Right hand and left hand specific versions are available.
Note: While this is an easily accomplished, non-permanent modification of the weapon, qualified armorer/gunsmith installation is recommended.
|
G. G. & G. M-4 / CAR-15 Agency Ambidextrous Receiver Sling Mount
SPECTER-DIRECT
Certain local, state and federal agencies have now established policies indicating that if a tool needs to be used to remove a part of the weapon to install a new accessory it cannot be done unless the weapon is sent to the agency's armorer or gunsmith for the installation. This has caused a problem for some agencies due to time constraints and the absence of local agency armorers. GG&G has developed the New Agency Rear Sling Adapter to assist these agencies with this issue. The new GG&G Agency Rear Sling Adapter only requires that the rear assembly of the collapsible buttstock be removed. No tools required. The new adapter then slides over the tube and, once in proper position, securely tightens behind the castle lock nut.
|
G. G. & G. AR-15 / M-16 Receiver Sling Mount (Rectangular Type)
SPECTER-DIRECT
Allows receiver side mounting of our CQB, SOP and HST slings on fixed stock AR-15/M-16 type weapons. Right hand and left hand specific versions are available.
Note: While this is an easily accomplished, non-permanent modification of the weapon, qualified armorer/gunsmith installation is recommended.
|
G. G. & G. Shotgun Receiver Sling Mount (Rectangular Type)
SPECTER-DIRECT
Allows receiver side mounting of our CQB, SOP and HST slings on Remington 870 / 11/87 or Mossberg 500 / 590 shotguns. Right hand and left hand specific versions are available.
Note: While this is an easily accomplished, non-permanent modification of the weapon, qualified armorer/gunsmith installation is recommended.
|
G. G. & G. AR-15 / CAR-15 Sling Thing
SPECTER-DIRECT
The G. G. & G "Sling Thing" is the most secure and efficient setup to secure a tactical "3 Point" type sling to AR-15 and CAR-15 type weapons. The front "Sling Thing" attaches to the standard AR-15 / CAR-15 front sight assembly offering a sling attachment mounted high enough to prevent rifle roll as well as allowing sling attachment for weapons equipped with the Surefire Millennium weapon light assemblies. The rear Sling Thing is mounted to the side of the collapsible buttstock on CAR-15 and M-4 type carbines. The "Sling Thing" is easy to install, and remove. It's ambidextrous, and there is no gunsmithing required. The "Sling Thing" utilizes M-16 type 1 1/4" sling loops and is phosphate finished to match your weapon.
|
G. G. & G. Quick Detachable (QD) Sling Things
SPECTER-DIRECT
Our “Sling Things” provide a lightweight, durable, easy-to-install and inexpensive method to do so. Both our standard front Sling Thing and front QD (Quick Detachable) Sling Thing install easily onto the M16/AR15’s “A-frame” front sight assembly, on either the right or left sides using socket head cap screws. Mounted high in this manner “rifle roll” is completely prevented. The rear Sling Thing is designed for easy attachment to the M16/AR15 collapsible stock. There are versions to fit either aluminum or synthetic types. The standard Sling Thing uses Colt 1¼-inch sling swivels.
|
G. G. & G. Rail Sling Mount & Swivel
SPECTER-DIRECT
Fits all MIL-STD-1913 Picatinney type rail interface fore end systems. This is particularly useful for units being issued the new M-16A4 without a side sling swivel assembly.
|
|
|
|
|
